Barry-Wehmiller Network
  • View Us on Facebook
  • View Us on LinkedIn
  • WordPress

Aftermarket Services

Current Offerings

*Price dependent upon application

For information on the Aero-Seal Closer, please contact:

Tim McArdle
P: (612) 782-1200
Email Here

For all other equipment, please contact:

​Dean Grell
P: (612) ​782-1271
Email Here

4420 Case Erector/Bottom Sealer (Hot Melt)

4460 Case Erector/Bottom Tape Sealer

The Model 4420 Automatic Case Erector/Bottom Sealer is designed to select a knockdown case from a vertical stack, positively open the case with opposing suction cups, tuck/plow and apply hot-melt adhesive to the bottom minor flaps, fold closed the major flaps, while compressing the minor flaps with ​RAM, and allowing the glue to set. This fully-automatic machine includes the following:

  • Machine layout for left hand fold cases
  • Six-foot long powered inline magazine
  • Nordson hot-melt adhesive glue tank
  • Servo ram for flap compression
  • Allen-Bradley PLC
  • Allen-Bradley operator interface
  • 240 volts AC, 60 Hz, 3-phase electrical service
  • 24 VDC control voltage
  • Compressed air requirement of 80 PSI (5.5 bar)
  • Factory check-out:  Up to 1 day (8 hours) for machine check-out at our manufacturing facility
  • Manuals (two sets) provided in CD-ROM
This case erector is an automatic machine designed to erect a knockdown corrugated case (RSC) and seal its bottom flaps with pressure sensitive tape. This machine is designed for extra deep cases. This machine includes the following:
  • Machine layout for right-hand fold cases
  • Extended Case Range Capability (Non-Standard)
    • Length - 6 in. - 24 in. (150 mm - 610 mm)
    • Width - 5.5 in. - 16 in. (140 mm - 406 mm)
    • Depth - 6.5 in. - 28 in. (165 mm - 711 mm)
  • Six-foot long knockdown magazine
  • A Dekka 3-inch tape head, painted mild steel
  • NEMA 12 electrical construction
    • NEMA 12 and/or IP65 rated electrical devices
    • NEMA 12, mild steel painted electrical enclosure
  • Allen-Bradley PLC
  • Push-button operator control station with cycle start, cycle stop, and E-stop
  • 220/230/240 volts AC, 50 or 60 Hz, 1-phase electrical service
  • 24 VDC control voltage
  • Compressed air requirement of 80 PSI (5.5 bar)
  • Factory check-out: Up to 1/2 day (4 hours) for machine check-out at our manufacturing facility (equipment is individually tested with burst runs, simulating real line operating conditions as feasible within our product handling capabilities)
  • Manuals (two sets) provided in CD-ROM​

SRx50 IM Cartoner with Glue

Servo Beverage Packer

This unit is an automatic intermittent cartoner for glued flap cartons, which can run at speeds up to 40 cartons per minute. It features a parallel infeed conveyor that can be retrofitted to come from either way. ​This machine includes the following:
  • 10-foot infeed conveyor constructed of mild steel with infeed buckets
  • The rotary carton setup has three pick and place vacuum heads
  • Powered, 4-foot horizontal magazine with a vibrator and photoeye to detect low carton level in the magazine
  • Product is loaded into the carton with a pneumatic or servo driven arm with a pusher face. A pneumatic cylinder lifts the arm after the load stroke to clear incoming product, returns to the load position, and is lowered
  • Nordson glue tank with two hoses and guns
  • A-B SensaGuard RF guard door interlock switches
  • Allen-Bradley PLC with built in Ethernet port
  • Allen-Bradley Panelview color touchscreen operator interface
  • 480 VAC, 60Hz, 3-phase electrical service
  • 24 VDC for all sensing devices and solenoid valves
  • Compressed air requirement of 80 psi (5.5 bar)
  • Manuals (two sets) provided in CD-ROM
  • Machine checkout includes one day with one carton size
The Servo Beverage Packer features a servo-coordinated axis motion control drive system, with hot melt closure system. Cartons are erected by a rotary carton setup unit, and product is loaded into the carton. If no carton is present, the cans can be rejected. The minor flaps are tucked closed, glue is applied and the major flaps are plowed closed. Cartons are discharged through side compression belts. This beverage cartoner can handle 12 and 24 packs (including Fridge Pack). This machine includes the following:
  • Left hand orientation
  • Six star wheel infeed system for cans or bottles
  • Standard rotary carton setup unit includes four pick and place heads
  • Eight-foot long powered carton magazine driven by a gear motor
  • The barrel cam loader gently pushes the product from the infeed buckets into the carton. It is equipped with an overload protection sensor to stop the machine if a jam occurs
  • Nordson glue system
  • Proportional valve for glue-pressure control to maintain consistent glue application volume with changes in the machine speed
  • Electrical interlock switches on guard doors
  • CompactLogix processor with ethernet ports
  • Allen-Bradley Panelview color touchscreen operator interface
  • 480 VAC, 60Hz, 3-phase electrical service
  • Compressed air requirement of 80 PSI (5.5 bar)​
  • Machine checkout includes one day with one carton size
  • Manuals (two sets) provided in CD-ROM

Used ​Series 4600 Aero-Seal Closer

​CPO Series 4600 Aero-Seal Closer

The Series 4600 Aero-Seal Closer is designed to close and seal the top of stepped-end, multiwall (PBOM) bags after the filling operation.  The unit activates the pre-applied adhesive on the stepped-end and fold over the top to seal the closure. 

Features standard with this unit include a crank adjustable elevating mechanism for height adjustment, built in auto tuning temperature controller, removable heater nozzle and folder blade, electronic heater control with LED readout, interlock switch on the front cover and an air safety switch to prevent damage to the air heater during an air pressure loss and tongue and groove compression belt design for ease of tracking. This machine includes the following:
  • Standard construction
  • Right to left feed
  • 2800 Watt heater
  • General Purpose Area classification
  • NEMA 12 electrical enclosures
  • Variable speed AC drive with 3/4 HP motor
  • TEFC motor
  • Step-down transformer from 460 Volt to 230 Volt 60 Hz
  • Two CD-ROM manuals supplied with machine
  • Reverse direction switch located on operators panel for clearing bag jams 
The Series 4600 Aero-Seal Closer is designed to close and seal the top of stepped-end, multiwall (PBOM) bags after the filling operation.  The unit activates the pre-applied adhesive on the stepped-end and fold over the top to seal the closure. 

Features standard with this unit include a crank adjustable elevating mechanism for height adjustment, built in auto tuning temperature controller, removable heater nozzle and folder blade, electronic heater control with LED readout, interlock switch on the front cover and an air safety switch to prevent damage to the air heater during an air pressure loss and tongue and groove compression belt design for ease of tracking. This machine includes the following:
  • Standard construction
  • Right to left feed
  • 3500 Watt heater
  • General Purpose Area classification
  • NEMA 12 electrical enclosures
  • Variable speed AC drive with 3/4 HP motor
  • TEFC motor
  • Step-down transformer from 460 Volt to 230 Volt 60 Hz
  • Two CD-ROM manuals supplied with machine
  • Reverse direction switch located on operators panel for clearing bag jams